Slurry Tanker T522 – 22 000 Liters

Suspension: TRIDEM (two spring-loaded axles)

These units feature a strong and compact construction. Thanks to well-chosen equipment, they offer short filling times and wide working widths. The wagons are available in four versions, allowing you to select the appropriate tires and compressor already at the offer creation stage.


📱 Marcin Górski: +48 691 897 575 | 📧 m.gorski@pomot.pl

📱 Łukasz Lechicki: +48 607 999 359 | 📧 l.lechicki@pomot.pl

Category: Tag:

Standard Equipment

  1. Tank

    • Tank hot-dip galvanized on both sides

    • Tank passivation protecting fresh galvanization from slurry corrosion

    • Rear hatch ø700 mm – hinged cover

    • Tubular fill level indicator with sight glass

    • Drain fitting with 1 ½” valve at the lowest point of the tank

    • 4” sight glass on the rear tank bottom

    • Upper hatch ø350 mm

    • 4” safety valve

    • 8” fitting on top of the tank, sealed – prepared for mounting a rubber filling funnel

    Vehicle Construction: Frame Type

    • FRAME TYPE – tank mounted on a frame made of closed-section profiles

    • Replaceable hitch – bolted ø50 mm

    • Mechanically adjustable support leg

    Running Gear

    • Tridem or hydraulic Tridem wheelset

    • Tires according to the table

    • Mudguards

    • Pneumatic dual-circuit brake system with 4-stage braking force adjustment

    • Manual parking brake

    Compressor

    • Type according to the table

    • PTO drive 540 or 1000 rpm – optional

    Additional Equipment

    • Reinforced temperature-resistant hoses connecting the fittings

    • Overflow protection with a two-ball valve with sight glass on top of the tank and a siphon with sight glass

    • Pressure gauge

    • Two safety valves: overpressure up to 0.05 MPa and underpressure up to -0.05 MPa

    • Oil separator – wet air filter, muffler to reduce compressor noise

    Suction Fittings

    • Suction fittings 6” ø150 mm

    • Main drain fitting in the rear hatch cover 6” with hydraulic slide valve 6”

    • Front left and right fittings sealed, prepared for manual slide valve installation

    • Rear fitting sealed, prepared for manual slide valve installation

    Electrical System

    • 12V electrical and lighting installation

    Suction Hose

    • Hose 6” (ø150)

    • Transport handles for suction hose

    • Hose with suction basket – protects against intake of large debris

    • Suction hose length – 6 meters

    Spreading Device

    • Profiled spreading shovel POMOT 94 pattern, spreading width up to 14 m

    Power Take-Off Shaft

    VERSION SUSPENSION TIRE DIMENSIONS TIRES COMPRESSOR TYPE
    ECONOMIC TRIDEM (including 2 steering axles) 1235×550 550/60×22.5 MEC 9000 or KD 10000
    STANDARD TRIDEM (including 2 steering axles) 1230×600 600/55×22.5 MEC 11000 or KD 12000
    CLASSIC TRIDEM (including 2 steering axles) 1340×600 600/55×26.5 MEC 11000 or KD 12000
    PREMIUM TRIDEM (including 2 steering axles) 1340×700 700/50×26.5 MEC 13500 or KD 12000

Optional Equipment

Spreading Devices

  • Wide-angle spreader (working width up to 14 m)

  • Slurry thrower (working width from 6 to 15 m)

  • Mobile device for road spraying and crop irrigation with water, 2.5 m wide

  • Mobile device for road spraying and crop irrigation with water, 4.5 m wide

  • PERROT type spreading shovel (working width up to 12 m)

  • Double spreading shovel (working width up to 16 m)

  • Trailed dribble bar system with 3 m working width by POMOT – mechanically foldable

  • Trailed dribble bar system with 3 m working width by POMOT – hydraulically foldable

  • Plant watering device

Chassis and Running Gear

  • Upper transport hitch (frame construction only)

  • Drawbar suspended on longitudinal spring

  • Ball hitch K80

  • Rear steering axle (only for T 546 type)

  • Hydraulic support leg

  • Hydraulic brake (for one axle)

  • 2 wheel chocks

Filling Systems

  • Additional manual slide valve 6”

  • Quick coupling for 6” manual slide valve

  • Extension for 6” suction hose, length 3 m

  • Extension for 6” suction hose, length 6 m

  • Additional 6” suction hose, length 6 m

  • Injector 4” or 6” – suction from up to 10 m depth

  • Hydraulic compressor drive

Accessories

  • Two galvanized metal hose boxes

  • Two galvanized metal boxes for transporting crop protection products

  • Scaling of tubular indicator with stickers

  • Fully openable rear tank bottom

  • Upper hatch Ø500 mm with ladder

  • Ladder

  • Fitting W52 with 2” ball valve

  • Pneumatic agitator

  • Hydraulic screw agitator

  • Wide-angle power take-off shaft

  • Plastic toolbox

  • Hand wash dispenser

  • Additional paint for galvanized tank (one side)

  • Additional paint for galvanized frame

NOTE – Other additional equipment options are also available (see accessories for slurry tankers tab).

Downloads

Videos